Latest Contributions by AlejandroMata

1812;168209 wrote: Once you have the POINT_X and POINT_Y of points and the NEAR_X and NEAR_Y in the same table (as I decribed in the beginning), you can use the XY To Line tool with the default Line Type - Geodesic, if you have ArcGIS 10. This tool creates a line using the two point coordinates in each row of your table. Hi Dan ! Im using ArcGis 9.3, if i dont have ArcGis 10, what can i do ? Greetings ! ... View more

Are you thinking the topology rule for points - "must be covered by" lines? It might give you the association between points and lines, but doesn't snap or move your points to the nearest lines. I think these are two different things. Hi Dan ! I want to make virtual lines to connect a point layer to a line layer, and i want that these lines are included in the lines layer. As the image shown below. [ATTACH=CONFIG]11578[/ATTACH] I was trying to make a topology with the rule " Point must be covered by lines ", it select all the points but i dont know how to create the lines to connect between the layers. Do you have some suggestion ? Thanks in advance. ... View more

Hi folks ! Thanks a lot for your suggestions, i'm going to test your advices and i tell you how i was. Regards. ... View more

That VBA uses "Debug.Print" and the output will show in the "Immediate" window. You may have to make that visible. Hi Jay ! You're all right, i didn´t have open "immediate" window, thanks. I wrote all the junctions to a file, but is there a way to relation txt file to Network Dataset Layer ? I mean, i would like to have in a shp file, all the junctions with their adjacent junctios and times. Best Regards. ... View more

Hi Anna ! Exactly it was that i wanted. You resolved one of my problems. Thanks a lot. ... View more

Anna ! In the image i got wrong in the numbering, it must to start in 2 in place of 1. Best Regards. ... View more

Hi Anna ! Ok, first all the orders are assigned. As you say i have " Time Windows, MaxTotalTime, MaxTotalTravelTime " etc, etc. But i want to find the way to change the order of the " Orders " (Prioritize as you said) I attached an image to show you what i want to do. After seeing the image, what do you thing that i have to do ? ... View more

Hi all ! Is very important for me to do what you mentioned in this thread. I followed the steps listed to get the distance between junctions but i haven´t achieved good results. I did that: 1.- Added the Network Dataset to ArcMap. 2.- The Network Dataset is the first layer in TOC. 3.- Added the VBA code to VBA Editor, i changed the EID to OID. 4.- Run the VBA and nothing happens. I have some doubts: 1.- Where it is supossed the results should be displayed ? 2.- The results are a new table ? a new attibute ? in what layer ? I hope you can help me. Best Regards. ... View more

Hi Rodelv, In order properties, there is a "Revenue" field. Orders can be prioritized by setting different values in this field. The higher revenue means a higher priority. You can set some positive Revenue values for orders with high priority. Solver will tend to assign those orders first. Please let me know if you have more questions. Thanks. Anna Hi Anna ! I want to prioritize the orders too, i tested what you said setting high values in Revenue field, but it doesn´t work. Solver do the same and it doesn´t change the Orders priority. What else can i do ? ... View more

Hi ! I don't have 10.0 release, it is the only way to solve it ? Do you know a solution to 9.3 release ? ... View more

Hi Anna ! I'm going to try to be more especific, but i apologize for my english and i hope that you understand me. Yes, all that you say is almost correct, i guess that you are understanding the problem that i have. Actually the route 1 (as well as other routes) starts from the Distribution Center with load for the whole week, the driver has a workday of 450 minutes per day, but as the stores are in another cities maybe the driver just can cover a store or two per day, then perhaps it´s not reasonable to return to distribution center. The driver can overnight at city of last store who attended, and the next day he can continue with the next store without return to the Distribution Center. My intention is to make routes more than two days, just one Distribution Center and the routes are not limited to a single day. I hope to be more clear and you can guide me. Greetings. ... View more

Hi Jorgen ! The problem that you have can be cause your shapefile (lines) is not correctly connected, at least between the two points that you have. I mean, maybe there is a broken line between the two points y for that reason it says that " Route nor found " First try to locate two points in a place where you know that the line is not broken to verify that your shapefile it´s ok. Greetings ! ... View more