POST
|
When attempting to add new fields to old surveys in survey123 connect I am getting an error code 400 service layer definition not found. The appears to be the case for any field that I enter even a simple integer at the end. Is this a common problem. Is this a common problem? Anyone else having this problem with older surveys? If I make a copy of the survey it works just fine.
... View more
11-25-2019
06:31 AM
|
0
|
1
|
375
|
POST
|
I was able to fix it. Basically doing the exact same thing only reversing the order of the portrait and landscape. I may have simply had a syntax error and rewriting the code caught the error not sure. Anyway if you have a photo log and want to show all landscape photos on a landscape page and portrait photos on a portrait page filling the entire page with the image and have a small amount of room at the bottom for photo attributes I have attached my form and report templates.
... View more
10-15-2019
03:52 PM
|
0
|
0
|
1041
|
POST
|
I am having the issue now with the latest release and my images which rendered previously will no longer render.
... View more
10-15-2019
01:02 PM
|
0
|
1
|
6621
|
POST
|
I am having some issues with the latest update to survey123 report template. I worked very hard getting a report template to print photos that were taken in landscape to fill the page with landscape orientation and photos taken in portrait to fill the page with portrait orientation with metadata for each photo attached. I have attached the template below. This took a lot of trial and error to get working. It worked fine with the desired results during beta and even into the initial release. With the latest release the ability to bypass saving reports to an account was removed. Now the template says it cannot render images. The template searches for and displays all landscape images on a page with landscape orientation. Then I inserted a section break and ran a similar code but only displaying photos that are portrait on a page with portrait orientation ${#photoLogBegin} ${if ((photo|getValue:"width")>2448)} ${photo|size:980:0} Site: ${siteNumber} | Project: ${projectNumber} | Image: ${imageNumber} | Aspect: ${bearing} | Tilt: ${tilt} | Photo By: ${photographer} |${dateSubmited} | ${shotTime} | ${photoPoint|getValue:”x”} ${photoPoint|getValue:”y”} ${photoDescription} ${/} ${/photoLogBegin} A section break is inserted here and the orientation is changed ${#photoLogBegin} ${if ((photo|getValue:"width")<3263)} ${photo|size:720:0} Site: ${siteNumber} | Project: ${projectNumber} | Image#: ${imageNumber} | Aspect: ${bearing} | Tilt: ${tilt} | PhotoBy: ${photographer} |${dateSubmited} ${shotTime} | ${photoPoint|getValue:”x”} ${photoPoint|getValue:”y”} ${photoDescription} ${/} ${/photoLogBegin} Just curious if anyone has had any success manipulating images this way. Also in the past I've had to use a lot of experimentation. Now that the reports come at a cost it seems like any experimentation with report templates also comes at a cost? Has anyone found a way to test report templates without incurring a cost?
... View more
10-15-2019
09:05 AM
|
0
|
1
|
1307
|
POST
|
I am having some issues with the latest update to survey123 report template. I worked very hard getting a report template to print photos that were taken in landscape to fill the page with landscape orientation and photos taken in portrait to fill the page with portrait orientation with metadata for each photo attached. I have attached the template below. This took a lot of trial and error to get working. It worked fine with the desired results during beta and even into the initial release. With the latest release the ability to bypass saving reports to an account was removed. Now the template says it cannot render images. The template searches for and displays all landscape images on a page with landscape orientation. Then I inserted a section break and ran a similar code but only displaying photos that are portrait on a page with portrait orientation ${#photoLogBegin} ${if ((photo|getValue:"width")>2448)} ${photo|size:980:0} Site: ${siteNumber} | Project: ${projectNumber} | Image: ${imageNumber} | Aspect: ${bearing} | Tilt: ${tilt} | Photo By: ${photographer} |${dateSubmited} | ${shotTime} | ${photoPoint|getValue:”x”} ${photoPoint|getValue:”y”} ${photoDescription} ${/} ${/photoLogBegin} A section break is inserted here and the orientation is changed ${#photoLogBegin} ${if ((photo|getValue:"width")<3263)} ${photo|size:720:0} Site: ${siteNumber} | Project: ${projectNumber} | Image#: ${imageNumber} | Aspect: ${bearing} | Tilt: ${tilt} | PhotoBy: ${photographer} |${dateSubmited} ${shotTime} | ${photoPoint|getValue:”x”} ${photoPoint|getValue:”y”} ${photoDescription} ${/} ${/photoLogBegin}
... View more
10-14-2019
12:31 PM
|
0
|
2
|
1007
|
POST
|
The issue we were having was using a Mac to create the checks works just fine on Windows after testing.
... View more
08-06-2019
03:48 PM
|
3
|
0
|
1749
|
POST
|
I am having the exact same problem. Load the template then just get empty checkboxes.
... View more
08-02-2019
02:21 PM
|
0
|
0
|
1749
|
POST
|
Thanks for the help. The problem is I have a set of coordinates in decimal degrees when I run the ConvertCoordinateNoatation tool it returns the UTMs as a string (e.g 13N6046424148283). I need this to be in 2 columns. (e.g coordinateX = 604642.396 coordinateY =4148283.7975) for every point in my table. I can get the UTMs by parsing the string that is returned by the ConvertCoordinateNoatation tool but I cannot get the precision as this is not returned by the ConvertCoordinateNoatation tool. Is there another tool or better way to do this in Python.
... View more
07-11-2019
12:05 PM
|
0
|
2
|
766
|
POST
|
I have coordinates in decimal degrees in one table. I need to convert them to UTMs in another table. I can use arcpy.ConvertCoordinateNoatation_management(input, output, geoLat, geoLong, "DD_2", "UTM ZONES"). This gives me the UTMS and I can index them to place them in a northing and easting column. The problem is the other table that I need to put these in has UTM coordinates as a floating point number. Is there a simple way to get the UTMs as a floating point number from the Decimal Degree Coordinates?
... View more
07-11-2019
10:32 AM
|
0
|
4
|
888
|
Title | Kudos | Posted |
---|---|---|
3 | 08-06-2019 03:48 PM |
Online Status |
Offline
|
Date Last Visited |
11-11-2020
02:23 AM
|