nav[aria-label="Primary Navigation"] { padding: 0; & ul { list-style: none; width: 100%; display: flex; flex-direction: row; justify-content: start; align-items: start; gap: 30px; padding: 0; & li { margin: 0; } & ul li { list-style: none; } } }

ArcGIS Pro stays in geocoder rematch mode

PeterHansen4

ArcGIS Pro 2.3 with 2 service pack patches installed. Longtime ArcMap user, recent Pro adopter.

-----

I'm probably missing something simple here, but after I geocode a list of addresses and work through the rematch process, subsequent clicks/uses of the Explore/default cursor sometimes seem to be interpreted as a map-click rematch suggestion for a geocode record. It manifests as the little "PP" icon on the map where I clicked. The rematch window is closed, and sometimes even the geocode layer that had been produced is not even in the map. How can I stop this behavior?

Thanks

タグ付けされた投稿をもっと見る

Accepted answers

All comments

MichaelMarlatt1

I've been experiencing this same problem in 2.6. According to the release notes for 2.7 it is fixed in that version. Search for BUG-000128312: In ArcGIS Pro, closing the Rematch Addresses pane do.. (esri.com)

I haven't had the new version installed yet but I'm crossing my fingers that this problem is resolved.

TravisHaney

Has there been any solve for this? I get the same thing.

DennisLatto1

Its the most frustrating thing EVER!. I cannot for the life of me end the **bleep** rematching process. Even after you save edits, its still there... How is there not an "End rematch" button????

DennisLatto1

I for the life of me cannot figure out how to STOP THE REMATCHING PROCESS. It is killing me! There needs to be a button that says "END REMATCH" or something. How is there now??

Kara_Shindle

I'm dealing with this right now in 2.6.2. I closed the rematch window, edits have all been saved. I just removed all the pertinent layers and saved ArcPro and the leftover rematch symbols are still there. Irritating. It's happened on every layer I've geocoded this month. It went away after I reopened ArcPro, but still, irritating. Screenshot below. Where would I find the rematch window to reopen and try to get rid of these?

rematch error.png Edit:

I RC my imported CSV table & clicked "geocode table." Used the ArcGIS World Geocoding Service.

This persists among multiple outputs from tools. My workflow takes the output of the geocode and does a few spatial joins, projects, and exports from a gdb to shapefile. I turn off previous layers and it still persists, but I've not removed them individually to test.

RichardQuodomine1

I'm on Pro 2.6.1 and the same problem continues.

Steps: Import table from .xlsx (MS Office 360) to the native project database.
Geocode said table.
Images of post-geocoding A, B, C etc. persist.
Suspicion: Needs to flush character.
Attempted solution #1: Remove and re-import geocoded table.
Status: Fail. A, B, C persist.
Attempted solution: Close and restart ArcGIS Pro.

Status: Successful.

I suspect that there's a persist in the Geocoder that isn't flushing all leftover data bits.

ShanaBritt

If you are still encountering this behavior, please provide your exact steps that can consistently reproduce this problem. This will be helpful for us to find a solution as I've not been able to reproduce the behavior. Based on some of the posts there look to be different paths to getting the Rematch mode to be stuck in a bad state.

-Shana

JamesColbert

I have the same problem too. Version 2.6.0

JosephCarpenter

Same issue for me.

DavidSolari

Hi Shana,

My team finally has Pro 2.5.1 and I can confidently say that this issue hasn't been fixed. All geocodes were performed using the World Geocoding Service.

ShanaBritt

David:

ArcGIS Pro 2.5 is available now. If you are able to install 2.5, run through your workflow again to see if you get the same behavior. It would be great for us to have specific steps and data (table, locator) to further investigate these types of issues so that we can fix them. Did you encounter this behavior with a locator created with the Create Address Locator tool, Create Locator tool, or the ArcGIS World Geocoding Service?

-Shana

DavidSolari

Same behavior from my end in 2.4.0 and 2.4.2 (not sure about 2.5 and up). Once you start rematching a layer that layer is stuck in a sort of rematch state, which constantly adds address candidates to the map view and automatically zooms in on the first record of a new selection. Closing the rematch pane doesn't fix this, only removing then adding the layer again, and even then the candidate icons (A, B, C etc.) are stuck on my end. Hopefully if this isn't fixed in 2.5 it's addressed soon.

Anonymous User

Shana:

I am sorry to say I do not have any more screenshots and do not have a need for geocoding another set at this time. I was using the public version of the Delaware geocoder (http://firstmap.delaware.gov/pdfs/public/FirstMapGeocoder.pdf ). If I experience this behavior again after the next update I will try going through support to resolve. Thank you

ShanaBritt

Sharon:

Are you able to include a screenshot that shows the status of the Rematch Addresses pane when this behavior occurs?

I can't tell what's going on in the ones you've already provided. In those it's odd that you have multiple A & B candidates.

Are you using a locator created with the Create Address Locator tool or the Create Locator tool?

This issue may also be better addressed through Support where you can provide the exact steps and possibly data. The next release of ArcGIS Pro will be available soon and if the behavior is still reproduced in the new release submit the issue through Support. During the development cycle of the next release of Pro we addressed some odd behavior with rematch.

Anonymous User

ArcGIS Pro 2.4.2

ShanaBritt

Sharon, which version of ArcGIS Pro were you using when encountering this behavior?

ShanaBritt

Bennett, which version of ArcGIS Pro are you using?

BennettMorris

I had this issue too. I also found that after you rematch addresses and select features using the interactive selection tool, the rematch process is somehow still active. I solved this by removing the feature class from the map, saving the Pro project and then I added the feature class back to the map. This worked for me.

Anonymous User

Same but mine is showing the A B C alternative locations for manually matched locations.

The table is already matched and there is a point under the A option.

See below where I bumped up the symbol size.

会話に参加する

サインインしたメンバーは投稿、更新のフォローなどができます。初めてですか？無料アカウントを登録してください。

クイックリンク

Community Help
Find useful guides, FAQs, and documents to help you navigate and make the most of Esri Community.