Používám Drone2Map 1.3.2. Mám sbírku fotografií, které byly <\/SPAN>nasbírány během letu dronem a jsou ve WGS 84. Spustil jsem je bez <\/SPAN>zemních kontrolních bodů a získal jsem pěkně vypadající mozaiky a povrchy. <\/SPAN>Pak jsem zkusil další projekt v Drone2Map se stejnými fotografiemi, a tentokrát <\/SPAN>se pokusil přidat zemní kontrolní body poskytnuté v CSV. Jsou <\/SPAN>ve Washington StatePlane South. V Arc Map se správně zobrazují jako <\/SPAN>Washington State Plane South. Import GCP do projektu v Drone2Map se zdá, <\/SPAN>že rozumí horizontálnímu souřadnicovému systému, a Sample <\/SPAN>Record ukazuje, že pole CSV byla správně načtena. Dropbox - gcp.PNG<\/A> Ale dostávám pouze "V projektové oblasti nejsou žádné GCP. <\/SPAN>Prosím zkontrolujte svůj prostorový odkaz a ověřte, zda jsou vaše zeměpisná šířka a <\/SPAN>zeměpisná délka správné." Co jsem přehlédl? Musím převést <\/SPAN>GCP na WSG 84? <\/SPAN><\/P><\/P>Přinesl jsem body State Plane CSV do Arcmap jako XY události, přeprojektoval je do WGS 84, spustil na nich nástroj AddXY, exportoval je zpět do CSV a pak znovu importoval GCP do D2M. Mapování polí muselo být trochu upraveno pro použití nového mapování polí WGS 84, ale body byly importovány bez problémů. Vytvořil jsem své odkazy a právě to znovu spouštím, abych zjistil, jak moc kontrolní body pomáhají produktům. <\/SPAN><\/P><\/BODY><\/HTML>
Hi @JEngvall,This is a pretty old post so the way we handle coordinate systems from that version has changed a bit. When importing control we do a validation of the X/Y (lat/long) fields to make sure that the points appear over the flight area. Do you happen to have points that are far away from the flight path? If so, then they might be causing the problem.
I would also double check that the field mappings didn't get swapped for latitude and longitude as sometimes the table formatting, especially tables without headers, can cause the automated field detection to not match properly. If you continue to have trouble importing your control, then please share the image coordinate system you are using and the one you are defining for the control. Regards,
Mark
I'm having the same issue. The photos is reprojected fine but the control points does not work: "No control could be imported into your project. Please check that the control you are trying to import is in the correct spatial reference and the control is within the project area." The control points are the same coordinate system as the project but still does not work.
Hi there,I have similar question.I'm trying to import GCPs into Drone2map version 2.3.Images from the drone are in WGS 84 so I left all the project in this coordinate system.Now I would like to improve project accuracy by GCPs, however according to this procedure:
I can not click on "OK". What might be the problem please?I can have GCPs either in national geographic system - "JTSK Krovak East North" or WGS.I tried to import both but without a success.I am looking forward for any suggestions.
I figured out that transformation on the fly does work in Drone2Map. I had just been trying to use the wrong input coordinate system for the GCPs. Drone2Map presents a lot of different kinds of NAD 1983 Washington State Plane South, and, unlike my ArcMap, none are saved to "favorites". NAD 83 Washington State Plane South 102349 sends the GCPs out of the project area. NAD 83 Washington State Plane South Feet 2927 places the GCPs correctly.
It looks like I don't have a processing report for this run. The report folder just has a folder html with the esri logo in it. I think that would be consistent with just stopping the project when I encountered the message that there were no control points in the project area. Would the report for the run in which I used reprojected coordinates be helpful?
Paul
Sorry for the delay in my response - I missed your original post. You *should* be able to use GCPs in state plane coordinates; there must be some other cause for this problem. Can you send us your processing report?
Cody B.
ESRI Technical support told me that having a different coordinate system for the ground control points just doesn't work. D2M is unable to reproject GCPs on the fly. That I should use my workaround workflow of changing the projection of the GCPs. But it seems strange that the product would have the user set the projection system for the photos in one area of the workflow, then have a way to define the projection system of the ground control points in another part of the workflow if it doesn't work.
Tech support pointed me to bug ENH-000103747, but this enhancement request doesn't match well to what I am experiencing. The bug description is "
Přihlášení členové mohou přispívat, sledovat aktualizace a další. Jste tu noví? Zaregistrujte si bezplatný účet.
Find useful guides, FAQs, and documents to help you navigate and make the most of Esri Community.
