https://community.esri.com/t5/arcgis-pro-questions/generate-service-area-fails-when-using-same/m-p/1062710#M41429 <P>For a few hours today I was working to generate some transit service maps, and I was able to do it just fine until it suddenly stopped working. It doesn't give any specific error message, just says "Generate Service Area Failed" about 1 second after clicking run. I've tried restarting the software, my computer, creating a new map and doing it fresh without other features there, I can't imagine what may have happened. Please if anyone has ideas it would be a huge help! Copied below are the settings I used and the "messages" at the bottom which just say there's no messages.</P><P>&nbsp;</P><P>Generate Service Areas<BR />=====================<BR />Parameters</P><P>Facilities stops1_XYTableToPoint2<BR />Break Values 5<BR />Break Units Minutes<BR />Analysis Region<BR />Travel Direction Away From Facility<BR />Time of Day<BR />Use Hierarchy false<BR />UTurn at Junctions Allowed Only at Intersections and Dead Ends<BR />Geometry at Overlaps Merge by Break Value<BR />Geometry at Cutoffs Rings<BR />Detailed Polygons false<BR />Polygon Trim Distance 100 Meters<BR />Polygon Simplification Tolerance 10 Meters<BR />Point Barriers in_memory\feature_set2<BR />Line Barriers in_memory\feature_set3<BR />Polygon Barriers c25orgreaterslope_Buffer1<BR />Restrictions 'Avoid Carpool Roads';'Avoid Express Lanes';'Avoid Gates';'Avoid Private Roads';'Avoid Stairways';'Avoid Unpaved Roads';'Roads Under Construction Prohibited';'Through Traffic Prohibited';Walking<BR />Attribute Parameter Values in_memory\record_set<BR />Time Zone for Time of Day Geographically Local<BR />Travel Mode Custom<BR />Impedance Walk Time<BR />Save Output Network Analysis Layer false<BR />Overrides<BR />Time Impedance WalkTime<BR />Distance Impedance Miles<BR />Polygon Detail Standard<BR />Output Type Polygons<BR />Output Format Feature Set<BR />Ignore Invalid Locations true<BR />Service Areas in_memory\feature_set<BR />Solve Succeeded<BR />Output Network Analysis Layer scratchfile<BR />Output Facilities in_memory\feature_set1<BR />Output Service Area Lines<BR />Output Result File scratchfile<BR />Output Network Analysis Layer Package scratchfile<BR />=====================<BR />Messages</P><P>Start Time: Thursday, May 27, 2021 11:25:53 PM<BR />Succeeded at Thursday, May 27, 2021 11:25:53 PM (Elapsed Time: 0.27 seconds)</P> Fri, 28 May 2021 03:29:21 GMT rmsinger 2021-05-28T03:29:21Z https://community.esri.com/t5/arcgis-pro-questions/generate-service-area-fails-when-using-same/m-p/1062710#M41429 <P>For a few hours today I was working to generate some transit service maps, and I was able to do it just fine until it suddenly stopped working. It doesn't give any specific error message, just says "Generate Service Area Failed" about 1 second after clicking run. I've tried restarting the software, my computer, creating a new map and doing it fresh without other features there, I can't imagine what may have happened. Please if anyone has ideas it would be a huge help! Copied below are the settings I used and the "messages" at the bottom which just say there's no messages.</P><P>&nbsp;</P><P>Generate Service Areas<BR />=====================<BR />Parameters</P><P>Facilities stops1_XYTableToPoint2<BR />Break Values 5<BR />Break Units Minutes<BR />Analysis Region<BR />Travel Direction Away From Facility<BR />Time of Day<BR />Use Hierarchy false<BR />UTurn at Junctions Allowed Only at Intersections and Dead Ends<BR />Geometry at Overlaps Merge by Break Value<BR />Geometry at Cutoffs Rings<BR />Detailed Polygons false<BR />Polygon Trim Distance 100 Meters<BR />Polygon Simplification Tolerance 10 Meters<BR />Point Barriers in_memory\feature_set2<BR />Line Barriers in_memory\feature_set3<BR />Polygon Barriers c25orgreaterslope_Buffer1<BR />Restrictions 'Avoid Carpool Roads';'Avoid Express Lanes';'Avoid Gates';'Avoid Private Roads';'Avoid Stairways';'Avoid Unpaved Roads';'Roads Under Construction Prohibited';'Through Traffic Prohibited';Walking<BR />Attribute Parameter Values in_memory\record_set<BR />Time Zone for Time of Day Geographically Local<BR />Travel Mode Custom<BR />Impedance Walk Time<BR />Save Output Network Analysis Layer false<BR />Overrides<BR />Time Impedance WalkTime<BR />Distance Impedance Miles<BR />Polygon Detail Standard<BR />Output Type Polygons<BR />Output Format Feature Set<BR />Ignore Invalid Locations true<BR />Service Areas in_memory\feature_set<BR />Solve Succeeded<BR />Output Network Analysis Layer scratchfile<BR />Output Facilities in_memory\feature_set1<BR />Output Service Area Lines<BR />Output Result File scratchfile<BR />Output Network Analysis Layer Package scratchfile<BR />=====================<BR />Messages</P><P>Start Time: Thursday, May 27, 2021 11:25:53 PM<BR />Succeeded at Thursday, May 27, 2021 11:25:53 PM (Elapsed Time: 0.27 seconds)</P> Fri, 28 May 2021 03:29:21 GMT https://community.esri.com/t5/arcgis-pro-questions/generate-service-area-fails-when-using-same/m-p/1062710#M41429 rmsinger 2021-05-28T03:29:21Z