POST
|
Yes, I submitted it as a bug back in March of last year and looks like it is fixed in release 2.3. Bug BUG-000112606
... View more
01-21-2019
12:59 PM
|
1
|
0
|
1554
|
POST
|
In ArcGIS Pro I am using the Share -> Export -> Map function to export a Map of the world. It is a flat map and therefore much wider than tall. When I export the map when the map view is zoomed to the full extents the resulting image file is not as wide as it should be and the edges of the world have been clipped off. If I zoom out the map view significantly (such that the map itself only fills a small area of the screen, then the exported image (while much smaller in size) shows the complete map. Since we always export a full view of the world map and only move where the map is centered at, we have selected to enable wrapping to make it much easier to move without inadvertently changing the zoom level, we'd like to be able to export from the full extent view and have the resulting image show the entire world. I have checked the extents of the layers and they all are set to the entire world. Is this a bug or is there something we can do so the export always matches the current map view? I added attachments to show exactly what is happening. Map1.png is an export from the Map1 Screenshot.png and Map2.png is an export of Map2 Screenshot.png. Thanks!
... View more
06-13-2018
09:32 AM
|
0
|
2
|
2073
|
POST
|
Thanks for replying. I did some clean-up work preparing the project to be a template and since then have not been able to reproduce the behavior. If it happens again I'll try to boil it down to the simplest scenario and send a project over. Les
... View more
03-05-2018
11:01 AM
|
0
|
0
|
694
|
POST
|
Maplex engine refuses to display labels on some views using an orthographic projection when zoomed out past a certain point (1:58,157,528 in this case). In particular this seems to mostly occur with Australia or the Far East as the center of the view. The labels will show once zoomed in a little if I pan the view toward the top of the screen or once I zoom in even more if I do not pan the view at all. If I pan back down without changing the zoom the labels disappear. Visibility Range is set to none for both In beyond and Out beyond. The labels do NOT show as unplaced labels when selecting View Unplaced. Selecting Unplaced labels, Never remove has no effect. Weights and Priorities are all at the defaults and changing them has no effect at the problem zoom level. Turning off all other layers also has no effect. The labels immediately display when changing to the Standard labeling engine. What am I missing?
... View more
03-01-2018
08:04 AM
|
0
|
3
|
940
|
POST
|
Thanks so much!. I had tried that DAML id as you mentioned as a "tool" with SetCurrentToolAsync(). I had also tried using an ICommand at one point but must have had the wrong DAML id.
... View more
02-28-2018
05:21 AM
|
0
|
0
|
762
|
POST
|
How can I programmatically start the (Edit) Annotation Tool in Modify Features? I have not been able to find a combination of a DAML id and Framework method that launches the Annotation Tool in the Tools section of the Edit tab.
... View more
02-27-2018
12:45 PM
|
0
|
2
|
972
|
POST
|
All, I have an old extension was used with ArcGIS 8.2. I believe it is a VB 6.0 extension that was written in 2004. I do not have the original source code for the extension so I cannot recompile. I ran the setup.exe of the original extension and also registered the dll using the ESRIRegASM utility - not sure if that was necessary or not. The toolbar for the extension is available, but the extension is not listed in the extensions list. When the toolbar comes up, at first of all the controls are enabled, but as soon as I click on the map, the extension toolbar's buttons and controls go to a disabled state. So my question is, should this old extension work as-is with ArcGIS 10.2 and, if so, what do I need to do to get the toolbar functions enabled? Thanks.
... View more
02-24-2014
04:07 PM
|
0
|
0
|
2596
|
Title | Kudos | Posted |
---|---|---|
1 | 01-21-2019 12:59 PM |
Online Status |
Offline
|
Date Last Visited |
11-11-2020
02:23 AM
|