BLOG
|
Our organisation is also waiting for the Windows OS version.
... View more
06-04-2019
01:48 PM
|
0
|
0
|
3388
|
IDEA
|
Hi Robert, Yes you are right, this probably would not be useful for users using lower accuracy GPS units. However users chasing centimetre accuracies will know the importance of following good survey practise to ensure their measurements have the appropriate checks therefore confirming the reliability of their data. I know users that have better quality GPS would like to measure survey control a 2nd time so it adds redundancy to their data-sets and confirms they are working in terms of the correct coordinate system. RTK GNSS observations on control marks are measured at least twice with a 20 – 30 minutes interval between observations as to check against ionospheric & tropospheric delay, multipath and receiver noise.
... View more
04-29-2019
01:23 PM
|
0
|
0
|
559
|
IDEA
|
As collector has started to support high-accuracy receivers it would be good to have the ability to follow good survey practise for GPS measurements. It would be good if we had to measure a point twice (say 20mins between each set of measurements) we could have the option of another set of measurements which would be used to calculate a weighted average position for the point using the two sets of measurements. This could also flag any error in a measurement if the 2 measurements did not agree within a certain limit. The second measurement on the point is to obtain an independent fix by having different satellites in a different constellation.
... View more
04-28-2019
05:59 PM
|
1
|
2
|
668
|
POST
|
Hi Geoffrey, Leica has updated their firmware for the GNSS receivers which now allows the GNSS receiver to connect directly to Collector while streaming the GST message.
... View more
04-28-2019
03:39 PM
|
2
|
0
|
2770
|
POST
|
Hi Geoffrey, Thanks for the reply. I have been using firmware 7.52. I have been in contact with Leica and this is the lastest reponse. "I think I’ve got to the bottom of this problem. From SmartWorx Viva v6.16 onwards the Bluetooth connection on our GS sensors supports two SPP (serial) ports instead of just one previously. We introduced this feature as a request from many other 3rd party applications. The second port is now commonly used to push the RTK data from any 3rd party application to the GS. The first serial port is the one, where the NMEA data is streamed. It seems that ArcGIS uses a service (you cannot directly set the port) to establish the connection and it expects only 1 SPP port from our device, but instead receives two and does not know what to do with it or uses the incorrect port. At the minute we cannot change the behaviour of our sensors, because it was a request from many 3rd party developers. Instead could you take a different approach to request ESRI to adapt their application?" Hopefully ESRI releases an update in the future that allows for Leica GPS senors to use the Collector App without having to download a 3rd Party app.
... View more
11-11-2018
12:37 PM
|
1
|
2
|
2770
|
POST
|
Update: I have talked to Michael Chourdakis (the developer of GPSdirect) and he has said the GST sentence cannot pass though the Windows sensor interfaces. This explains the 2nd question I had about collector receiving the GST message through the GPSDirect Driver. I am still keen to know why collector will not allow me to select the Leica GS16 GPS receiver directly over Bluetooth as a location profile receiver
... View more
08-14-2018
05:11 PM
|
0
|
0
|
2770
|
POST
|
Hi Matthew, Thanks for the suggestion, however I don't think the Lecia GS16 can connect to Lecia Zeno Connect as this is for the GG02/03/04 units. I think the app NTRIP Client for Android could be used to connect to RTK. Regards
... View more
08-14-2018
05:07 PM
|
0
|
2
|
2770
|
POST
|
I have been trying to pair a Lecia GS16 GPS receiver with Collector (running on a Panasonic FZ-G1) however I have run into a few issues and therefore I have a few questions. I can connect the Lecia GS16 GPS receiver with the Panasonic FZ-G1 and use the Captivate software to connect to RTK and set the NMEA output to; GGA GSA GSV RMC VTG GST Then in collector I tried to add the GS16 GPS receiver as the location provider however when I try to 'switch' from the integrated receiver to the GS16 GPS receiver (which is connected via Bluetooth) the error message "connection failed" appears. I closed Captivate so no programs were using the GPS sensor and used PuTTY to test the NMEA stream (screenshot attached below). 1) What is the cause of this error message and is there anyway to connect the GS16 directly to collector? Is it not connecting due to an error in the NMEA messages? After coming across the above issue I then tried to work around it by installing GPS Complete and installing the GPSDirect Driver and selecting the NMEA source as the COM port (COM5) that the GPS receiver is connected too. When I test COM5 I can see all 6 NMEA messages being streamed (including the GST message) Back in collector I selected the integrated receiver as the location provider. The location of the "integrated receiver" was showing the location of the GPS receiver however the Horizontal Accuracy and Vertical Accuracy were shown as 2m when Captivate was showing the true accuracy to be around 25mm. Since the accuracy isn't being shown as 25mm in collector I think that Collector isnt reading the GST message through the integrated receiver. 2) Are there any specific setting that are required when setting up the GPSDirect Driver to get the GST message through to Collector? or is the GPSReverse (COM Port Driver) required to be installed? Miaogeng Zhang Any help will be much appreciated Thanks Hugh
... View more
07-17-2018
09:59 PM
|
1
|
10
|
3844
|
POST
|
Hi Morgan, Thanks for your reply, so is there no way to for Collector to read the GST sentence from Zeno Connect even though the GG04 can output the GST message through Zeno Connect? Is there a way to create a COM port that Zeno Connect can output the full NMEA message and the Collector App can recognise it? Or is the way you described above the only way to connect the GG04 to Collector Thanks
... View more
09-12-2017
06:26 PM
|
1
|
2
|
1702
|
POST
|
Hi, I am trying to connect our Leica GG04 to Collector through a virtual serial port driver but collector is not opening the port and is saying it is in use. However when I use another program to open the virtual COM port it shows the NMEA message being streamed. Any Ideas, Thanks Hugh
... View more
09-11-2017
10:57 PM
|
0
|
7
|
3167
|
Title | Kudos | Posted |
---|---|---|
1 | 11-11-2018 12:37 PM | |
2 | 04-28-2019 03:39 PM | |
1 | 04-28-2019 05:59 PM | |
1 | 07-17-2018 09:59 PM | |
1 | 09-12-2017 06:26 PM |
Online Status |
Offline
|
Date Last Visited |
11-11-2020
02:23 AM
|